Robotics
This is an 11 tooth steel gear. This gear fits onto the 9015 motor shaft so that the 9015 motor can mate with the PG27 gearbox.
Specifications:
This cable can be used in many ways, a power cable for the Gorgon Flex, or from a Speed Controller to a CIM motor. One end connectors are crimped with PowerPole Connectors, two crimps and a black and red housing are shipped with this cable. Tip-to-tip length is approximately 24 inches.
Specifications:
This is 12 GA bonded wire* with Red and Black Jacketing. It is much easier to use than two separate wires, easier to follow during troubleshooting, and easier to keep your wiring clean. Pull apart at the end only as much as you need and the rest stays together.
If you are looking for a much more flexible wire or wire that is not bonded check out our Silicone Wire.
* - This is also known as zip cord or zip wire.
This 120 Amp Circuit breaker forms the main circuit breaker for FIRST Robotics Competition robots. It can protect your robot or other system from drawing so much current that systems receive more damage. Of course, we highly recommend using circuit breakers downstream rated for less to protect your motors, speed controllers, and control system components.
Specifications:
The 120 Degree Bracket is perfect for connecting two channel pieces at 120 degrees from each other. Each side is 48mm wide to fit perfectly on the channel. Use three brackets with 3 channel pieces to make 3 wheeled robots. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
Specifications:
Servo City's patented 32 pitch Hitec metal gears are designed to attach directly to the output spline of a servo. All gears are broached directly into the metal to ensure a snug fit that will not slip. These gears are designed to fit the standard 24 tooth Hitec output spline.
Specifications:
This 12 tooth pinion gear is designed to fit onto an AndyMark RedLine Motor (am-3775) and other motors with a 5 mm output shaft to interface with spur gearboxes such as the DeCIMate (am-3745), EVO Slim for RedLine and EVO Shifter for RedLine.
Specifications:
This gear comes standard as the pinion for the NeveRest motor, am-3104
Specifications:
The Studica 12V 3,000 mAh NiMH (nickel metal hydride) Battery Pack, PP45 comes with a w/20 amp fuse. It is a 10-cell, 12-volt rechargeable battery that brings long-lasting power to motors and electronics that are used in the WorldSkills Mobile Robotics Collection. The Studica NiMH Battery Pack Charger, PP45, is required to charge the battery.
This battery is NOT COMPETITION LEGAL for FIRST TECH CHALLENGE or FIRST ROBOTICS COMPETITION.
Specifications,
The 135 Degree Bracket is perfect for connecting two channels pieces at 45 degrees from each other. Each side is 48mm wide to fit perfectly on the channel. Used for intake systems, elevator systems, or structure where 45 degrees is required. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.
Specifications:
1.420 inch long spacer, with 3/8" nominal id (0.42 actual), made from 3/8" schedule 80 gray PVC pipe
Specifications:
Specifications:
This is the 14 tooth gear in the Toughbox which has a 3/8 inch hex bore.
Specifications:
This is a 15 Degree Bracket used in the Ramp.
Specifications: