This gear is used as the input pinion gear for the EVO Shifter. This gear is a tight press fit onto a CIM gear, and requires at minimum a 3-ton arbor press to install. If a CIM motor with this gear pre-installed interests you, check out am-0255_15T. 

Specifications:

• Tooth Count: 15
• Diametral Pitch: 32
• Pressure Angle: 20
• Pitch Diameter: 0.469"
• Face Width: 0.531"
• Thickness: 0.75"
• Material: 1117 Steel
• Bore: 0.312" Round (7.92mm) This is a press fit onto the CIM Motor (am-0255)
• Weight: 0.019 Lbs

This pinion gear attaches to an rs-550 or rs-540 motor so it can be used with a BaneBots P60 gearbox.

Specifications:

• 15 Tooth
• Material: Steel
• Bore: 3.2mm
• Gear Thickness: 0.35"
• Boss Length: 0.106"
• Boss Diameter: 0.219"
• Weight: 0.008

This gear can be used on the any of the PG Series Gearmotors, fitting on the 10mm output shaft. 

Specifications:

• Number of Teeth: 16
• Diametral Pitch: 20
• Pitch Diameter: 0.8"
• Pressure Angle: 14.5 Degrees
• Pitch Diameter: 0.8"
• Face Width: 0.55"
• Overall Width: 0.58"
• Bore: 10mm (0.395") diameter hole w/ 4mm (0.158") keyway
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.08 Pounds

This pinion gear attaches to an CIM style motor or gearbox so it can be used with a CIM Sport Gearbox.

Specifications:

• Tooth Count: 16
• Module: 0.7
• Pressure Angle: 20
• Pitch Diameter: 0.44 in.
• Overall Length: 0.35 in.
• Material: Steel
• Bore: 0.312" Round (7.92mm) This is a press fit onto the CIM Motor (am-0255)
• Weight: 0.008 Pounds

This pinion gear press fits on the AndyMark 9015 motor and is the pinion gear for the PG71 and PG188 gearboxes. 

Specifications:

• Number of teeth: 17
• Module: 0.6
• Pitch diameter: 10.2 mm
• Pressure angle: 20 degrees
• Bore: 0.1245-0.1265"
• Overall thickness: 0.315"
• Material: 1215 Steel

This pinion gear is designed to be pressed onto motors with a 5mm output shaft such as most 700 class motors. This pinion interfaces with our PG71 and PG188 gearboxes.

Specifications:

• Number of teeth: 17
• Module: 0.6
• Pitch diameter: 10.2 mm
• Pressure angle: 20 degrees
• Bore: 0.196 inch
• Overall thickness: 0.315 inch
• Material: Steel

Specifications: 

• Material: 4140 Steel
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Number of teeth: 17
• Pitch diameter: 0.85 inch
• Bore: 0.313 inch (8mm), with 2mm keyway
• Gear face width: 0.375 inch
• Weight: 0.04 pound

This is 18 AWG (gauge) bonded wire* with Red and Black Jacketing. It is much easier to use than two separate wires, easier to follow during troubleshooting, and easier to keep your wiring clean. Pull apart at the end only as much as you need and the rest stays together.
 

* - This is also known as zip cord or zip wire.

Specifications

• Gauge: 18 AWG
• Length: 25 feet
• Total Weight: lbs
• Weight: 0.45 lbs/ft
• Wire Jacketing: black & red (bonded together)

185x385, nylon, 0.625 od, 0.385 id, 0.185 thick, white

Specifications:

• Material: White Nylon Plastic
• Inside Diameter: 0.385"
• Outside Diameter: 0.625"
• Thickness: 0.185"
• Weight: 0.0014 Lbs

Specifications:

• Tooth Count: 18
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 0.9"
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex

Specifications:

• Material: 1215 Steel
• Teeth: 19
• Diametral pitch: 32
• Pitch diameter: 0.59375"
• Bore: 0.376" Hex Bore
• Face Width: 0.44"

Steel dowel pin.

Specifications:

• Length: 1.0 inch
• Diameter: 0.25 inch
• Material: Hardened steel

Steel dowel pin, used in all AndyMark Plastic and Aluminum Omni Wheels as roller axles. These are NOT used in the Dura Omni Wheels.

Specifications:

• Length: 1.0"
• Diameter: 0.125"
• Material: Hardened Steel
• Weight: 0.0034 Lb

Omni-directional wheels in the smallest diameter offered by any common FIRST Robotics Competition or FIRST Tech Challenge supplier.

These 50 mm / 2 inch omni wheels features two different durometers:

• Soft 35A rollers for high traction
• Hard 90A rollers for long life

They also have a standard 14 mm Hex Bore, letting you choose between 3 different bores:

• 0.375 in. Hex - includes 14 mm Hex to 3/8 in. Hex Adapter (am-3905)
• 0.5 in. Hex - includes 14 mm Hex to 1/2 in. Hex Adapter (am-3904)
• 14 mm Hex - no adapters included

Stack several of these wheels on a shaft to craft an unstoppable intake system for your robot that can be used to center game pieces.

Specifications

• Bore: 0.375 in. Hex, 0.5 in. Hex, 14 mm Hex
• Diameter: 50 mm, 1.96 in.
• Durometer: 35A, 90A
• Load Capacity: 10 lbs
• Material: Glass Filled Nylon Body, Acetal Inserts, Thermoplastic Elastomer Rollers
• Weight: 0.076 lbs