This is 12 GA bonded wire* with Red and Black Jacketing. It is much easier to use than two separate wires, easier to follow during troubleshooting, and easier to keep your wiring clean. Pull apart at the end only as much as you need and the rest stays together.

If you are looking for a much more flexible wire or wire that is not bonded check out our Silicone Wire. 
 

* - This is also known as zip cord or zip wire.

Specifications

• Gauge: 12 AWG
• Length: 25 feet
• Total Weight: 1.2 lbs
• Weight: 0.05 lbs/ft
• Wire Jacketing: black & red (bonded together)

This 120 Amp Circuit breaker forms the main circuit breaker for FIRST Robotics Competition robots. It can protect your robot or other system from drawing so much current that systems receive more damage. Of course, we highly recommend using circuit breakers downstream rated for less to protect your motors, speed controllers, and control system components.

Specifications:

• Weight: 0.24 pounds
• Size: 2.9 x 1.9 x 1.5 inches
• Surface Mount Style
• Terminal Supply part number: CB3-SM-120
• Type III Breaker Manual Reset

Servo City's patented 32 pitch Hitec metal gears are designed to attach directly to the output spline of a servo. All gears are broached directly into the metal to ensure a snug fit that will not slip. These gears are designed to fit the standard 24 tooth Hitec output spline.

Specifications:

• Number of teeth: 12
• Diametral pitch: 32
• Pitch diameter: .375
• Face width: 0.250"
• Bore: 24T Servo Spline
• Weight: 0.008

This 12 tooth pinion gear is designed to fit onto an AndyMark RedLine Motor (am-3775) and other motors with a 5 mm output shaft to interface with spur gearboxes such as the DeCIMate (am-3745), EVO Slim for RedLine and EVO Shifter for RedLine. 

Specifications:

• Bore: 5mm press fit
• Weight: 0.014 Pounds
• Material: 1117 Steel
• Overall Length: 0.755 in.
• Face Width: 0.625 in.
• Tooth Count: 12
• Pitch Diameter: 0.375 in.
• Pressure Angle: 20
• Diametral Pitch: 32

This gear comes standard as the pinion for the NeveRest motor, am-3104 

Specifications:

• Module: 0.5
• Tooth Count: 12
• Pressure Angle: 20 Degrees
• Helix Angle: 18 Degrees, Left
• Bore: 2.98mm

1.420 inch long spacer, with 3/8" nominal id (0.42 actual), made from 3/8" schedule 80 gray PVC pipe 

Specifications:

• Material: 3/8 inch schedule 80 PVC pipe
• Inside diameter: 0.42 inch
• Outside diameter: 0.68 inch
• Length: 1.420 inch
• Weight: 0.02 pounds

Specifications:

• Tooth Count: 14
• Diametral Pitch: 20
• Pressure Angle: 14.5
• Pitch Diameter: 0.7
• Face Width: 0.375"
• Material: 4140 Steel
• Bore: 0.375" Hex
• Weight: 0.029 Lbs

This is the 14 tooth gear in the Toughbox which has a 3/8 inch hex bore. 

Specifications:

• Number of teeth: 14
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Pitch Diameter: 0.7 inch
• Face width: 0.575 inch
• Overall width: 0.600 inch
• Bore: 0.377 inch hex hole
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.1 lbs.

This is a 15 Degree Bracket used in the Ramp.

Specifications:

• Thickness: 0.09"
• Width: 1.0"
• Hole Size: 0.128"
• Material: 5052 Aluminum

This gear is used as the input pinion gear for the EVO Shifter. This gear is a tight press fit onto a CIM gear, and requires at minimum a 3-ton arbor press to install. If a CIM motor with this gear pre-installed interests you, check out am-0255_15T. 

Specifications:

• Tooth Count: 15
• Diametral Pitch: 32
• Pressure Angle: 20
• Pitch Diameter: 0.469"
• Face Width: 0.531"
• Thickness: 0.75"
• Material: 1117 Steel
• Bore: 0.312" Round (7.92mm) This is a press fit onto the CIM Motor (am-0255)
• Weight: 0.019 Lbs

This pinion gear attaches to an rs-550 or rs-540 motor so it can be used with a BaneBots P60 gearbox.

Specifications:

• 15 Tooth
• Material: Steel
• Bore: 3.2mm
• Gear Thickness: 0.35"
• Boss Length: 0.106"
• Boss Diameter: 0.219"
• Weight: 0.008

This gear can be used on the any of the PG Series Gearmotors, fitting on the 10mm output shaft. 

Specifications:

• Number of Teeth: 16
• Diametral Pitch: 20
• Pitch Diameter: 0.8"
• Pressure Angle: 14.5 Degrees
• Pitch Diameter: 0.8"
• Face Width: 0.55"
• Overall Width: 0.58"
• Bore: 10mm (0.395") diameter hole w/ 4mm (0.158") keyway
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.08 Pounds

This pinion gear attaches to an CIM style motor or gearbox so it can be used with a CIM Sport Gearbox.

Specifications:

• Tooth Count: 16
• Module: 0.7
• Pressure Angle: 20
• Pitch Diameter: 0.44 in.
• Overall Length: 0.35 in.
• Material: Steel
• Bore: 0.312" Round (7.92mm) This is a press fit onto the CIM Motor (am-0255)
• Weight: 0.008 Pounds

This pinion gear press fits on the AndyMark 9015 motor and is the pinion gear for the PG71 and PG188 gearboxes. 

Specifications:

• Number of teeth: 17
• Module: 0.6
• Pitch diameter: 10.2 mm
• Pressure angle: 20 degrees
• Bore: 0.1245-0.1265"
• Overall thickness: 0.315"
• Material: 1215 Steel

This pinion gear is designed to be pressed onto motors with a 5mm output shaft such as most 700 class motors. This pinion interfaces with our PG71 and PG188 gearboxes.

Specifications:

• Number of teeth: 17
• Module: 0.6
• Pitch diameter: 10.2 mm
• Pressure angle: 20 degrees
• Bore: 0.196 inch
• Overall thickness: 0.315 inch
• Material: Steel