Shafts, Adapters & Collars
This is an optional long steel output shaft for the Toughbox>® series gearboxes. This shaft includes a pre-installed magnet designed specifically with the E4T OEM Miniature Optical Encoder (am-3132) and SRX Magnetic Encoder (am-3445) encoder in mind. This shaft has replaced am-0211.
Usage:
Specifications:
This shaft is a replacement shaft for all PG Series Gearboxes. If your existing gearbox shaft has been damaged from the intensity of robotic competitions, you might not need to replace an entire gearbox, but just the shaft. The PG series gearboxes have 3 different shaft styles. Some have the shaft welded to a plate. Be sure your gearbox is a non welded version before ordering this replacement shaft.
Specifications:
This is an optional long steel output shaft for the Toughbox® series gearboxes. This shaft includes a pre-installed magnet designed specifically with the E4T OEM Miniature Optical Encoder (am-3132) and SRX Magnetic Encoder (am-3445) encoder in mind. This shaft has replaced am-0397.
Specifications:
This is an optional keyed steel output shaft for the Toughbox® series gearboxes. This shaft includes a pre-installed magnet designed specifically with the E4T OEM Miniature Optical Encoder (am-3132) and SRX Magnetic Encoder (am-3445) encoder in mind. This shaft has replaced am-0153. When used in a Toughbox Series gearbox this shaft needs to be supported with a 1/2 in. round bearing such as am-0030.
Usage:
Specifications:
This new custom designed collar clamp has been designed specifically with FIRST Robotics Competition teams in mind. This product is Out of Stock until Mid March
This is the small cluster gear shaft inside of the Toughbox series of gearboxes. This shaft goes into these gearboxes; Toughbox, Toughbox Mini, Toughbox Micro, Toughbox Nano, and NanoTube.
Specifications:
This is the output shaft for the RAW Box with a 1/4-20 tapped hole on one end and a 1/4" extended shaft on the other end (for an encoder mount).
Specifications:
These adapters are intended to be a high strength solution to adapt the Falcon Spline to any product that has a 1/2 in hex bore. This product includes the correct size washers to retain items along the hex shaft, as well as a thread-patch 8-32 screw to be used in conjunction with spacers included with the Falcon 500 motor to retain motion hardware.
1/2 in. hex shaft is the life of many competitive robot components. This 1018 steel shaft is available in four lengths. The five inch shaft was used in various Modulox gearboxes and may come with a 1/4 in. hole drilled in one end. The other sizes can be used as shaft stock, ready to be cut to length as needed. The stock lengths ship un-plated ready for your choice of finish.
This is the 1/2 in. hex steel output shaft for the Toughbox® series gearboxes when used with the AM14U5.
The AM14U5 uses round bearings in the outside plate rather than hex bearings. As a result, this shaft differs from previous AM14U output shafts by having a round portion at the end.
Thanks to the feedback from teams, we've made different versions of this shaft available. If you're using magnetic encoders and need magnets in your shaft, you can order shafts that come with magnets. Want to use non-magnetized dowels for your encoders? We have those too. Don't plan on using encoders? Save some money and order them without pins or magnets.
Options:
This shaft originally was the secondary output for the RocketBox PTO. This shaft connected the drive motors to the winch instead of the wheel output. This shaft can find a home in your custom gearbox design.
This shaft was originally used in our After Burner PTO. This shaft may find a use in your custom gearbox application. This shaft is intended to be used as a part of a shift mechanism. The shaft has a 0.188 in. long through-slot to be used with a shift assembly.
This is an optional replacement output shaft for our CIM Sport, 57 Sport, Dual 775 Sport and Falcon Sport gearboxes. This shaft protrudes 2 in. from the face of the gearbox. If your application requires a slightly longer output shaft, you can disassemble the gearbox and swap for this shaft. Need an output even longer? Try the 3 in. long output shaft.
1/2 in. hex shaft is the life of many competitive robot components. This 1018 steel shaft is available in four lengths. The five inch shaft was used in various Modulox gearboxes and may come with a 1/4 in. hole drilled in one end. The other sizes can be used as shaft stock, ready to be cut to length as needed. The stock lengths ship un-plated ready for your choice of finish.
PRE-ORDER Only shipping January 2023
Φ20.0mm*8.0mm thick
2*M3 thread for M3 SHCS
on the clamp side
Φ6.0mm D hole
AL6061-T6