Close
Main Categories
    Filters
    Preferences
    Search

    Plates

    Plates

    View as Grid List
    Sort by
    Display per page

    AMP Stage Plate (am-2286)

    #am-2286
    $23.06
    (In stock)

    This is the Carrier Plate w/ Sun Gear for the AM Planetary gearbox. Five planet gears (not included) ride on the dowel pins pressed into this part. Referencing the picture above, those dowel pins are protruding out the bottom side of the carrier plate.

    Specifications:

    • Weight: 0.07 pounds
    • Diameter: 1-3/8"
    • Length: 15/16"
    • Tooth Count: 15
    • Diametral Pitch: 32
    • Pressure Angle: 20 degrees
    • Pin Diameter: 0.125"
    • Gear Material: 1117 Steel

    Side Plate for RAW Box (am-2358)

    #am-2358
    $23.06
    (In stock)
    Two of these plates make up the outsides and house the RAW Box.

    Plate Spacer for RAW Box

    #am-2359
    $15.38
    (In stock)

    The Plate spacer goes on the opposite side of the RAW box from the CIM Motor. 

    Specifications:

    • Material: 6061 Aluminum
    • Length: 3.5"
    • Height: 1"
    • Thickness: 0.312"
    • Weight: 0.07 Pounds

    3 Motor Toughbox Shaft Plate (am-2386)

    #am-2386
    $21.53
    (In stock)

    This is the aluminum shaft plate for our 3 Motor Toughbox. A standard Toughbox could be converted to a 3 Motor Toughbox by using this plate and also the 3 Motor Toughbox Motor Plate.

    Specifications:

    • Size: 5x5x0.125 inches
    • Material: 6061 Aluminum
    • Weight: 0.274 pound
    • Finish: Tumbled

    3 Motor Toughbox Motor Plate (am-2387)

    #am-2387
    $23.89
    (In stock)

    This is the aluminum motor mount plate for our 3 Motor Toughbox. A standard Toughbox could be converted to a 3 Motor Toughbox by using this plate and also the 3 Motor Toughbox Shaft Plate.

    Specifications:

    • Size: 5x5x0.25 inches
    • Material: 6061 Aluminum
    • Weight: 0.528 pound
    • Finish: Tumbled

    SpinBox Shaft Plate, Flange (am-2457)

    #am-2457
    $15.38
    (In stock)
    This 1/8" thick plate supports the output shaft of the SpinBox gearbox. This plate has the same outer size as the SpinBox Housing.

    SpinBox Shaft Plate, Small (am-2463)

    #am-2463
    $9.23
    (In stock)
    This 1/8" thick plate supports the output shaft of the SpinBox gearbox. This plate has the same outer size as the SpinBox Housing.

    Sonic Gearbox Motor Plate (am-2506)

    #am-2506
    $30.75
    (In stock)
    This is the plate on the Sonic Shifter that is on the motor side. This plate has two 1/4-20 steel threaded inserts pressed in to one end of the plate.

    Wheel Conversion Plate with Nub Bore

    #am-2609a
    $12.50
    (In stock)

    This conversion plate acts as a hub between larger motion components featuring a 1.875" bolt circle to components of a smaller mounting circle such as a NeveRest Gearmotor. The bore of this plate fits shafts that are familiar to FIRST Tech Challenge teams.

    Specifications:

    • Material: 5052 Aluminum
    • Bore: 0.320" (8.1mm)
    • Outside Bolt Pattern: 0.204" diameter holes on a 1.875" diameter circle
    • Inside Bolt Patterns:
    • Four - 0.150" (3.8mm) diameter holes on a 0.630" (16mm) diameter circle
    • Four - 0.160" (4mm) diameter holes on a 0.770" (19.5mm) diameter circle
    • Outside Diameter: 2.125" from side to side
    • Thickness: 0.125"
    • Material: 5052 Aluminum

    Arm Joint Plate (am-2692)

    #am-2692
    $15.38
    (In stock)


    The Plate used in the PVC Arm Joint

    Specifications

    • Height: 3.505"
    • Length: 5"
    • Material: 6061 Aluminum
    • Thickness: 0.188"
    • Weight: 0.22 lbs

    Compression Spring, 0.50" L, 0.30" OD, 0.026" Wire, Steel Zinc Plated

    #am-2777
    $2.31
    (In stock)

    This is a steel compression spring made from music wire. It has closed and ground flat ends, and is zinc plated.

    Specifications:

    • Length: 0.50 inch
    • Outside diameter: 0.30 inch
    • Wire Diameter: 0.026 inch
    • Compressed Length: 0.13 inch
    • Spring Rate: 11.3 pounds/inch
    • Maximum Load: 4.3 pounds

    NeveRest Motor Plate

    #am-3104_plate
    $3.85
    (In stock)
    This motor plate fits onto the NeveRest Motor, am-3104. This plate allows a NeveRest Motor to be attached to a NeveRest gearbox.

    Toughbox Micro Angled Shaft Plate (am-3228)

    #am-3228
    $15.38
    (In stock)
    The Angled Shaft Plate is one plate option for the Toughbox Micro. This plate allows the TB Micro to be mounted to existing robot structure.

    Toughbox Micro Flat Shaft Plate (am-3229)

    #am-3229
    $25.59
    (0 In stock)

    The Flat Shaft Plate is one plate option for the Toughbox Micro. This plate allows the TB Micro to be mounted to existing robot structure.

    TileRunner Inside Plate

    #am-3392_Inside
    $23.06
    (In stock)

    This sheet metal plate makes up the inner plate of the TileRunner.

    Specifications:

    • Plate Length: 17.75"
    • Plate Height (flange to flange): 3.5"
    • Material Thickness: 0.09"
    • Material: 5052 Aluminum
    • Weight: 0.59 Pounds

    TileRunner Outside Plate

    #am-3392_Outside
    $21.53
    (In stock)

    Specifications:

    • Plate Length: 17.75"
    • Plate Height (flange to flange): 3.5"
    • Material Thickness: 0.09"
    • Material: 5052 Aluminum
    • Weight: 0.55 Pounds