48T, 20DP, 500 Key Bore Gear.

Specifications:

• Material: 4140 Steel
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Number of teeth: 48
• Pitch diameter: 2.4"
• Bore: 0.5" Round with 0.125" Keyway
• Thickness: 0.375"
• Thickness with hub: 0.4"
• Weight: 0.306 Lbs

Specifications:

• Material: 1215 Steel
• Teeth: 19
• Diametral pitch: 32
• Pitch diameter: 0.59375"
• Bore: 0.376" Hex Bore
• Face Width: 0.44"

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear.

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear.

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear.

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear.

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear. Check out the FlexHub Flyer 

Specifications

• General Info: All Flex Hubs fit all Flex Hub gears
• Hub Outside Geometry: 3/4 in. hex
• Hub Width: 0.400-0.410 in.
• Material: 12L14 steel

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear.

Introducing FlexHub, designed by engineers from iR3 Creative Engineering, from Orlando, Florida. FlexHub is a modular gear & hub solution from iR3 Creative. The concept is pretty simple. There is a hub, there is a gear, there are two retaining rings. Put them together into your assembly. If the gear ratio / shaft size / output / whatever isn’t working rinse and repeat with a new hub or gear.

This is the 14 tooth gear in the Toughbox which has a 3/8 inch hex bore. 

Specifications:

• Number of teeth: 14
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Pitch Diameter: 0.7 inch
• Face width: 0.575 inch
• Overall width: 0.600 inch
• Bore: 0.377 inch hex hole
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.1 lbs.

Specifications: 

• Material: 4140 Steel
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Number of teeth: 17
• Pitch diameter: 0.85 inch
• Bore: 0.313 inch (8mm), with 2mm keyway
• Gear face width: 0.375 inch
• Weight: 0.04 pound

The Worm Gear the is connected to the Output Drive Shaft of the RAW Box. 

Specifications: 

• Material: Brass
• Gear type: Worm
• Pressure angle: 25 degrees
• Number of teeth: 40
• Bore: 1/2" Hex
• Overall thickness: 0.25"
• Weight: 0.15 pound

Specifications:

• Material: 4140 steel, cold formed
• Diametral pitch: 20
• Pressure angle: 14.5
• Number of teeth: 24
• Pitch diameter: 1.2 inch
• Bore: 1/2" Hex (0.501-505 inch)
• Thickness: 0.38
• Weight: 0.086 pound

Specifications:

• Material: 4140 steel, cold formed
• Diametral pitch: 20
• Pressure angle: 14.5
• Number of teeth: 35
• Pitch diameter: 1.75 inch
• Bore: 8mm (0.315 inch) with 2mm keyway
• Thickness: 0.35 inch
• Weight: 0.23 pounds

This pinion gear is designed to be pressed onto motors with a 5mm output shaft such as most 700 class motors. This pinion interfaces with our PG71 and PG188 gearboxes.

Specifications:

• Number of teeth: 17
• Module: 0.6
• Pitch diameter: 10.2 mm
• Pressure angle: 20 degrees
• Bore: 0.196 inch
• Overall thickness: 0.315 inch
• Material: Steel