This gear is used on the Super Shifter, as a standard gear for the final stage. It is paired with the 45 Tooth Gear 20 dp 1/2 Hex Bore 0.57 Wide. 

Specifications:

• Number of teeth: 20
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Pitch Diameter: 1 inch
• Face width: 0.55 inch
• Overall width: 0.58 inch
• Bore: 0.502 inch diameter hole w/ 1/8" keyway
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.09 lbs.

This gear fits on the shaft of a CIM Motor. 

Specifications:

• Material: 4140 steel
• Number of teeth: 15
• Diametral Pitch: 20
• Pressure angle: 14.5 degrees
• Pitch Diameter: 0.75 inch
• Bore: 0.313 inch, with 2mm keyway
• Width: 0.375 inch
• Weight: 0.038 pounds

Specifications:

• Tooth Count: 15
• Diametral Pitch: 20
• Pressure Angle: 14.5 degrees
• Pitch Diameter: 0.75"
• Face Width: 0.46"
• Bore: 0.377" Hex
• Material: 4140 Steel
• Weight: 0.1 Pounds

This part can replace the steel Large Output Gear on the Toughbox, and save 0.28 pounds. 

Specifications:

• Material: 6061 Aluminum
• Diametral pitch: 20
• Pressure angle: 14.5
• Number of teeth: 50
• Pitch Diameter: 2.5 inch
• Bore: 1/2" hex hole, broached
• Coating: Nituff®
• Thickness: 0.342" face, with 0.40" width at hub
• Weight: 0.144 Lb

This gear presses on to the 2.5" CIM Motor. This gear smoothly presses onto the shaft of a CIM Motor, attaching to the shaft with only the friction press fit. No set screw, machine key, or collar clamp is needed. 

Specifications:

• Number of teeth: 15
• Diametral pitch: 32
• Pressure Angle: 20 degrees
• Pitch Diameter: 0.46875"
• Bore: 0.311-0.312"
• Thickness: 0.375"
• Weight: 0.012 Lb
• Material: 1117 Steel

This gear fits on the motor shaft of the AndyMark 9015 Motor.

Specifications:

• Material: 1215 Steel
• Teeth: 19
• Diametral Pitch: 32
• Pitch Diameter: 0.59375"
• Bore: 0.125"
• Face Width: 0.44"

This is a 12 tooth CIM Gear which is 0.52" long.

Specifications:

• Material: 4140 Steel
• Diametral pitch: 20
• Pressure angle: 14.5
• Number of teeth: 12
• Pitch Diameter: 0.60"
• Bore: 0.314" (8mm) diameter, with 2mm keyway
• Face width: 0.52"
• Weight: 0.028 Lb

Specifications:

• Number of teeth: 56
• Diametral pitch: 20
• Pressure angle: 14.5 degrees
• Pitch Diameter: 2.8"
• Face width: 0.344"
• Overall width: 0.380"
• Bore: 0.502" hex hole
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.6 lbs.

This gear can be used in the Toughbox, replacing the 14 tooth small cluster gear. It would be paired with a 48 Tooth Large Output Gear, in order to increase the output speed of the Toughbox. 

Standard Toughbox output reduction: 12.76:1 
Using this gear and a 48 Tooth Large Output Gear yields a 10.71:1 ratio.

Specifications:

• Number of teeth: 16
• Diametral pitch: 20
• Pitch diameter: 0.8"
• Pressure angle: 14.5 degrees
• Face width: 0.575"
• Overall width: 0.600"
• Bore: 0.377" hex hole
• Material: 4140 Steel, cold formed into gear teeth
• Weight: 0.1 Lb

This gear can be used in the Used in the Toughbox, replacing the 50 Tooth Large Output Gear. It would be paired with a 16 Tooth Small Cluster Gear, in order to increase the output speed of the Toughbox. 

Standard Toughbox output reduction: 12.76:1
New Toughbox output reduction, using this gear and a 16 Tooth Small Cluster Gear: 10.71:1 

Specifications:

• Material: 4140 Steel
• Diametral pitch: 20
• Pressure angle: 14.5
• Number of teeth: 48
• Pitch diameter: 2.4"
• Bore: 1/2" hex hole, broached
• Thickness: 0.4"
• Weight: 0.41 Lbs

This is the Output Gear used in the CIM-Sim and TB3 Gearboxes.

Specifications:

• Weight: 0.19 Lb
• Material: 4140 Steel, cold formed
• Diametral Pitch: 32
• Pressure Angle: 20 degrees
• Number of Teeth: 60
• Pitch Diameter: 1.875"
• Bore: 3/8" Hex
• Thickness: 0.40" overall, 0.345" face width

This is the Motor Gear used in the CIM-Sim Gearbox.

Specifications:

• Weight: 0.02 pound
• Material: 1117 steel
• Diametral Pitch: 32
• Pressure Angle: 20 degrees
• Number of Teeth: 12
• Pitch Diameter: 0.375 inch
• Bore: 0.125 inch
• Overall Width: 0.505 inch
• Face Width: 0.375 inch

Aluminum version of 45T 20DP Hex Bore Steel Gear (am-0179).

Specifications:

• Material: Aluminum
• Diametral pitch: 20
• Pressure angle: 14.5
• Number of teeth: 45
• Pitch diameter: 2.25"
• Bore: 1/2 inch hex hole, broached
• Thickness: 0.40"
• Weight: 0.13 Lb

This is the 48 Tooth Gear that can be used in place of am-0885. 

Specifications:

• Material: 6061 Aluminum
• Diametric pitch: 20
• Pressure angle: 14.5
• Number of teeth: 48
• Pitch diameter: 2.4"
• Bore: 1/2" Hex hole, broached
• Thickness: 0.4"
• Weight: 0.14 Lb

This pinion gear press fits on the AndyMark 9015 motor and is the pinion gear for the PG71 and PG188 gearboxes. 

Specifications:

• Number of teeth: 17
• Module: 0.6
• Pitch diameter: 10.2 mm
• Pressure angle: 20 degrees
• Bore: 0.1245-0.1265"
• Overall thickness: 0.315"
• Material: 1215 Steel

This gear can be used on the any of the PG Series Gearmotors, fitting on the 10mm output shaft. 

Specifications:

• Number of Teeth: 16
• Diametral Pitch: 20
• Pitch Diameter: 0.8"
• Pressure Angle: 14.5 Degrees
• Pitch Diameter: 0.8"
• Face Width: 0.55"
• Overall Width: 0.58"
• Bore: 10mm (0.395") diameter hole w/ 4mm (0.158") keyway
• Material: 4140 steel, cold formed into gear teeth
• Weight: 0.08 Pounds