Close
Main Categories
    Filters
    Preferences
    Search

    Electronics

    Electrical & Electronic Components

    View as Grid List
    Sort by
    Display per page

    JST-GH to JST-GH Cable

    #70168
    $1.38
    (2085 In stock)

    The JST-GH to JST-GH Cable connects external sensors, breakout boards or other devices.

    Detailed Specifications:

    • Cable Length: 25 cm
    • Connectors: 4-pin JST-GH (2)
    • Wire Colors: Black, Red, Blue, Green

    Maverick 12V DC Gear Motor w/Encoder

    #75001
    $39.00
    (813 In stock)

    Our improved and  stronger 12-volt DC motor with 100 rpm and 708 oz-in. of torque. The motor features a built-in, high-resolution Hall effect encoder for precise motor control and comes with an encoder cable.

     

    A 61:1 gearbox comes standard.

     

    Motor Specs

     

    Function

    Min

    Nom

    Max

    Input Voltage

    12VDC

    Gear Ratio

    1:61

    No Load RPM

    88

    100

    112

    No Load Current

    600mA

    Rated Speed

    68

    80

    92

    Rated Current

    2.2A

    Rated Torque

    139oz-in

    Stall Current

    11A

    Stall Torque

    708oz-in

    Direction

    CW

    Encoder Voltage

    4

    5

    Encoder Current

    6mA

    Encoder CPR

    6

     

    Output Counts per Revolution of Output Shaft (cpr) 1,464 pulses

     

    This motor is not FTC Compeition Legal

    MD2 Motor Driver & Sensor Adapter for NI myRIO

    #71010
    $262.54
    (500 In stock)

    The MXP-MD2 is a next-generation high performance Motor Controller Driver and Sensor Adapter with many added features to make it ready to use in your robot project. The included VNH5019ATR-E Motor Controller ICs are very robust with high current output and several important protection features. Many other I/O options have been incorporated into this design to make it extremely easy to interface to several different sensors.

    Features,

    • Includes 2 VNH5019 Motor Controller ICs,
      • 2 Enable Inputs, 2 direction inputs, one PWM input per channel up to 20Khz
      • Up to 12A Continuous output per channel, 30A peak current short ms duration
      • Under-voltage, over-voltage, reverse-voltage protection
      • Thermal Shutdown protection
      • Current Limit protection
      • Current Sense Output Proportional to Motor Current (approx. 140 mV/A)
      • Loss of Ground and Loss of Vcc Protection
      • Protection against short to Ground and short to Vcc

    Specifications,

    • 3V-compatible inputs
    • Directly interfaces with myRIO MXP Port
    • 8-16V DC Battery Input Terminal, J7, (GND, MTRS+ PWR)
    • Jumper Selectable Current sense feedback from the VNH5019 Motor ICs, J12, J17
    • Reverse Power LED Indicator
    • FWD and REV Motor Direction LED Indicators
    • 3 Servo Headers, J9, J10, J11, (SIG, SVDC, GND)
    • 1 Parallax Ping Sensor Port, J13, (GND, VCC, DIO)
    • 1 Sharp IR Port, J21, (AI0, VCC, GND)
    • 1 LSB Port, J18, (VCC AI0, AI1, AI2, AI3, GND)
    • 1 NavX Port, J19, (VCC, SDA, SCL, GND)
    • 2 Encoder Ports, J22, J23, (VCC, ENCB, GND, ENCA)
    • 1 I2C Port, J20, (NC, SCL, SDA)
    • Built in 5V 3A voltage Regulator
    • 3.3V Power Rail Header, J3, from myRIO
    • 5V Power Rail Header, J4, from onboard regulator
    • GND Rail Header, J6
    • Separate Servo Power Input, J8 (SV+ PWR, GND)

    Multi-Mode Smart Servo

    #75002
    $33.32
    (2211 In stock)

    The Studica Multi-Mode Smart Servo features all-steel gears and large amounts of torque. This angular programmable Servo can fill a variety of roles on your robot or project. In standard mode, it operates on a +/- 150-degree range. Using the Studica Smart Robot Servo Programmer (sold separately) the Multi-mode Smart Servo can be configured to run in continuous, standard, and custom angular mode. In continuous rotation mode, the servo will have proportional speed control based on the PWM signal that you send with your servo controller.  

    Specifications:

    Type:                             Metal Brush Motor
    Horn Gear Spline:       25T (5.9mm)
    Size:                               40mm x 20.1mm x 38.3mm
    Weight:                          65g
    Maximum Speed:        62RPM at 6V
    Stall Torque:                 20kg.cm at 6V
    Voltage:                         6-7 4V
    Cable:                             22AWG, 75cm

    MXP Extender Cable

    #69003
    $5.54
    (620 In stock)

    Extend the reach of your MXP port by using this 8 inch cable to re-position you boards where you need them.

    Features:

    • Keyed male and female 34-pin connectors
    • 28 AWG ribbon cable
    • 34 conductor
    • 8″ length

    myDAQ 20 Pin Screw Terminal Block Connector

    #70161
    $10.40
    (99 In stock)

    Used to replace or supplement connector on NI myDAQ Kit

    NiMH Battery Pack Charger, PP45

    #70019
    $41.66
    (1783 In stock)

    The Studica NiMH Battery Pack Charger, PP45, is used to recharge the 12V 3,000 mAh NiMH Battery Pack, PP45

    Specifications

    • Rating AC Input: 100V to 240V AC, 0.6A RMS, 50/60 Hz
    • Rating Output: 7V to 16 VDC
      • 0.9A to 1.8A
    • Protection mode: output short circuit protection and output polarity reverse protection.
    • Temperature range 0C ~+40C (battery pack)
    • Operate Humidity: 5% ~ 90%

    LED Indication

    Red Normal Main Charge mode
    Green Normal Finished / Open mode
    Red / Green Flashing Short Circuit

     

    ON/OFF Power Switch

    #66327
    $17.21
    (0 In stock)

    Studica ON/OFF Power Switch controls the power from the battery pack.

    Powerpole 45 Extension Cable, 14AWG, 50cm

    #70021
    $8.95
    (1029 In stock)

    The Powerpole Extension Cable is 50cm long and 14AWG wire gauge to handle heavier loads.

    PWM cable Set - TJC8 3 pin, 22AWG, F-F - 12 pcs

    #71011
    $22.21
    (1206 In stock)

    This set of 12 pieces includes,

    • 2 x 20cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 2 x 40cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 2 x 60cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
    • 6 x 3pin Dupont male to male connectors

    Servo Power Block

    #75006
    $51.38
    (1572 In stock)

    The Studica Servo Power Module is a 6V, 60W power injector that enables the use of high-power RC servos. The Servo Power Module passes through input signals unaltered while providing up to 60W of total output power across all eight channels.  The input and output channels accept standard 3-wire, 0.1” pitch, servo/PWM cables. 

    Features,

    • Built in DC-DC converter
    • Over-current shutdown
    • ESD protection

    Specifications,

    • Nominal Input Voltage: 12V
    • Operational Voltage Range: 6.0V
    • Number of Channels: 8
    • Max Current for All Channels Combined: 10A
    • Total Continuous Power: 60W
    • Size: 70mm x 45mm x 16mm
    • Step File

     

    Short Lever Limit Switch with Terminals (4 pack)

    #72060
    $13.88
    (1086 In stock)

    This is a snap-action micro switch with hinged roller lever and terminals for easy wire connection.

     

    Features:

    • High precision of action seat
    • High shock resistance
    • Shock resistance Max.l000/s2
    • Max temperature: T105.C
    • Catheter design for easy wiring 
    • 3 Pin
    • Max. Current: 16A
    • Max. Voltage: 250V
    • OP:14.3~15.1mm
    • Protection Level: IP40
    • Switch Function: ON - (OFF), OFF - (ON)
    • Contact form: SPDT
    • High impact resisstance
    • Max Ambient temperature:105centigrade
    • Mechanical life:10,000,000 on -off
    • Electrical life: over 100,000 on-off
    • Contact material: AgNi ,AgCdO
    • Certificate: CCC,CE,UL,ROHS
    • Step File

     

    Smart Robot Servo Programmer

    #75003
    $18.04
    (2097 In stock)

    The Studica Smart Robot Servo Programmer is used for programming the Studica Multi-Model Smart Servo Motor and for testing other standard Servos. Use it to program the Studica Servo to switch between continuous mode, standard mode, or any custom angular mode.  

    Specifications:

    • Requires 6 Volt battery pack with TJC8 connector or use the Studica 6V DC Battery Holder.
    • Programming setting modes
      • Standard
      • Continuous
      • Angular

    Titan Cable Pack

    #70162
    $9.71
    (458 In stock)

    The Titan Cable Pack contains three cables. A 60cm CAN Wire for connecting the Titan Motor Controller to a CAN 2.0B capable device and two (idk the 50cm JST-VH to JST-VH cables for connecting 12VDC power to other devices such as the VMX or Servo Power Block.

    • 2 - JST-VH to JST-VH cable
      • 50cm
    • 1 - CAN Wire
      • 60cm

    Titan Quad Motor Controller

    #70152
    Request a Quote

    The Titan Quad Motor Controller is a powerful, 4-channel CAN-based motor controller with a built-in fuse-box (for DC motors up to 20A).

    Features:

    • 4 x Hardware encoder ports – one for each motor
    • 2 limit switch ports for each motor
    • Fuse box to set manual current limits
    • 2x Power extension ports to power other 12VDC devices. I.E.
      • VMX Robotics Controller
      • Servo Power Module
    • Built in LED Controller
    • 6A power supply for LED’s
    • i2c communication port to control LED Controller
    • USB ports are updated to USB-C to better support todays cable standards
    • Step File

    Ultrasonic Distance Sensor

    #70753
    $24.99
    (1604 In stock)
    • Stable, accurate distance measurement
    • High precision, blind spots (3cm) super close
    • A full set of ranging process
    • Step File